Camera Module Board for Respberry Pi 2 REV 1.3 5MP Webcam Video 1080p 720p Fast 
Description : High Quality Camera Module Board for Raspberry Pi,The photosensitive chip module uses OmniVision company’s 1/4 inch OV5647 chip, It’s able to deliver a crystal clear 5MP resolution image, or 1080p HD video recording at 30fps! Latest Version 1.3! The Raspberry Pi Camera Board Features a 5MP (2592×1944 pixels) Omnivision 5647 sensor in a fixed focus module The module attaches to Raspberry Pi, by way of a 15 Pin Ribbon Cable, to the dedicated 15-pin MIPI Camera Serial Interface (CSI) The CSI bus is capable of extremely high data rates, and it exclusively carries pixel data to the BCM2835 processor The sensor itself has a native resolution of 5 megapixel, and has a fixed focus lenson board The camera is capable of 2592 x 1944 pixel static images, and also supports 1080 p @ 30 fps, 720 p @ 60 fps and 640 x480 p 60/90 video recording The camera is supported in the latest version of Raspbian, the Raspberry Pi’s preferred operating system Specification: Fully Compatible with Both the Model A and Model B Raspberry Pi 5 MP Omnivision 5647 Camera Module Still Picture Resolution: 2592 x 1944 Video: Supports 1080 p @ 30 fps, 720 p @ 60 fps and 640 x480 p 60/90 Re cording 15-pin MIPI Camera Serial Interface Size: Approx. 25 x 24 x 9 mm /0.99 x 0.95 x 0.36 inch Package Included: 1x Camera Module Board for Raspberry Pi How to enable camera support in Raspbian Boot up the Pi and log in. The default username is pi, and the default password is raspberry. (Note: if you have changed these from the default then you will need to supply your own user/password details). Run the following commands in a terminal to upgrade the Raspberry Pi firmware to the latest version: sudo apt-get update 
Click to enlarge sudo apt-get upgrade 
Click to enlarge Access the configuration settings for the Pi by running the following command: sudo raspi-config Navigate to “camera” and select “enable”. 
Click to enlarge 
Click to enlarge Select “Finish” and reboot. 
Click to enlarge How to use the Raspberry Pi camera software raspivid is a command line application that allows you to capture video with the camera module, while the applicationraspistill allows you to capture images. -o or –output specifies the output filename and -t or –timeout specifies the amount of time that the preview will be displayed in milliseconds. Note that this set to 5s by default and that raspistill will capture the final frame of the preview period. -d or –demo runs the demo mode that will cycle through the various image effects that are available. Example commands Capture an image in jpeg format: raspistill -o image.jpg Capture a 5s video in h264 format: raspivid -o video.h264 Capture a 10s video: raspivid -o video.h264 -t 10000 Capture a 10s video in demo mode: raspivid -o video.h264 -t 10000 -d To see a list of possible options for running raspivid or raspistill, you can run: raspivid | less raspistill | less Use the arrow keys to scroll and type q to exit. Extended documentation is available. Note that we recommend that you change SSH password if you are using a camera, in order to prevent unwanted access. How to stream video from the Raspberry Pi camera over a network To view the feed on Linux Install the dependencies by running the following in a terminal: sudo apt-get install mplayer netcat Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX). Run the following command in a terminal to view the feed using MPlayer: nc -l -p 5001 | mplayer -fps 31 -cache 1024 – To view the feed on Windows Install and run Linux instead. Find your IP address by running ipconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX). Download MPlayer. Download Netcat. Note that your browser may complain that these files are malicious, as they are unsigned executables. Press the Windows key and the ‘r’ key simultaneously to bring up the “Run” dialog. Enter cmd.exe into the dialog and press enter/return to open a DOS prompt. Enter the following command at the prompt to view the feed using MPlayer: [Path to nc.exe]nc.exe -L -p 5001 | [Path to mplayer.exe]mplayer.exe -fps 31 -cache 1024 – To view the feed on OS X Download MPlayer. Alternatively, you can download mplayer using Brew, which we recommend. Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX). Run the following command in Terminal to view the feed using MPlayer: nc -l -p 5001 | mplayer -fps 31 -cache 1024 – To view the feed on a Raspberry Pi: Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX). Run the following commands in a terminal on the receiving Pi: mkfifo buffer nc -p 5001 -l > buffer | /opt/vc/src/hello_pi/hello_video/hello_video.bin buffer To transmit the feed from the Pi with camera module attached After setting up the “receiving” machine as per the instructions above, run the following commands in a terminal on the “transmitting” Pi: raspivid -t 999999 -o – | nc [insert the IP address of the client] 5001 You can then use the commands listed in the “How to use the Raspberry Pi camera software” section above to change the capture time or to add a video effect. 
1.We accept Alipay, West Union, TT. All major credit cards are accepted through secure payment processor ESCROW. 2.Payment must be made within 3 days of order. 3.If you can’t checkout immediately after auction close, please wait for a few minutes and retry Payments must be completed within 3 days. 
1. WORLDWIDE SHIPPING. (Except some countries and APO/FPO) 2. Orders processed timely after the payment verification. 3. We only ship to confirmed order addresses.Your order address MUST MATCH your Shipping address. 4. The images shown are not the actual item and are for your reference only. 5. SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season. 6. If you have not received your shipment within 30 days from payment, please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! 7. Due to stock status and time differences, we will choose to ship your item from our first available warehouse for fast delivery. 
1. You have 7 days to contact us and 30 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and WE WILL NOT ISSUE YOU A REFUND OR REPLACEMENT. There are NO EXCEPTIONS! Shipping cost is bear by both seller and buyer in half. 2. All returned items MUST BE in the original packaging and you MUST PROVIDE us with the shipping tracking number, specific reason for the return, and your po#. 3. We will refund YOUR FULL WINNING BID AMOUNT, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER BOTH Buyer and Seller cancel the transaction from aliexpress. OR, you may choose to have a replacement. 4. We will bear all the shipping cost if the product(s) is (are) not as advertised. 
1. 12 months Manufacturer`s limited Warranty for defective items (excluding items damaged and/or misused after receipt). Accessories come with a 3-month warranty. 2. Defective items MUST BE reported and returned within the warranty period (and in the original packaging, if possible). You must tell us what the defect is and give us your order number. WE DO NOT REPAIR OR REPLACE ITEMS WITH AN EXPIRED WARRANTY. 3. You agree to all of the above-listed policies upon ordering on Aliexpress! 
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them.
